XSW 1-908

En slagkraftig framføring. Alt-i-ett trådløst system for messingblåseinstrumenter, enkelt i bruk.
Article No. 507101

Overview

En slagkraftig framføring. Gå for XS WIRELESS 1, og du kan stole på solid trådløs overføring med opptil 10 kompatible kanaler i et stabilt UHF-bånd.
XS WIRELESS 1 messingblåsersett er et alt-i-ett trådløst system, enkelt i bruk, spesielt utviklet for å gi en slagkraftig livelyd for messingblåseinstrumenter. Settet inneholder en stasjonær mottaker for raskt oppsett, problemfri håndtering og intuitiv betjening, samt en kompakt lommesender og en robust kondensator svanehalsmikrofon.


Features

  • Allsidig svanehalsmikrofon med fremragende lydgjengivelse fra den berømte mikrofonserien evolution

  • Diversity mottak med antenne-svitsjing

  • Integrerte antenner

  • Automatisk frekvenshåndtering og synkronisering via ekstern kanal for enkelt oppsett

  • Valgbare UHF-frekvenser innenfor en stor båndbredde

  • Opptil 10 kompatible kanaler


Hva er med i esken?

  • 1 mottaker EM-XSW 1
  • 1 svanehalsmikrofon e908T
  • 1 lommesender SK-XSW
  • 1 strømforsyning NT 12-5 CW
  • 2 AA-batterier

Technical Data

Receivers

  • Dimensjoner
    ca. 200 x 42 x 127 mm
  • Vekt
    cirka 340 g (mottaker)
  • Strømtilførsel
    Receiver: 12 V DC nom. / 300 mA
  • AF frekvensrespons
    Mottaker: 50 Hz til 16 000 Hz (-3 dB)

Transmitter

  • Dimensjoner
    ca. 71 x 96 x 28 mm
  • Vekt
    ca. 95 g
  • Strømtilførsel
    Transmitter: 2 AA size batteries, 1.5 V
  • Adjustment Range Transmitter
    0 til -30 dB, justerbar i 10 dB trinn
  • Microphone
    kondensator
  • Total harmonisk forvrengning (THD)
    ≤ 0.9%
  • Mønster for opptak
    kardioide
  • Signal-til -støy-forhold
    ≥ 103 dBA
  • RF utgangeffekt
    10 mW
  • Skiftende båndvidde
    opp til 24 MHz
  • Driftstid
    cirka 10 timer
  • Modulasjon
    bredbånd FM
  • Output voltage
    1/4" (6,3 mm) jack-kontakt (ubalansert): +6 dBu, XLR-kontakt (balansert): +12 dBu
  • Housing
    robust ABS-hus
  • Frequency
    8 frekvensbanker, hver med opptil 10 fabrikkinnstilte kanaler
  • Frekvensområder
    A: 548-572 MHz, GB: 606-630 MHz
    B: 614-638 MHz
    C: 766-790 MHz
    D: 794-806 MHz
    E: 821-832 MHz, 863-865 MHz
    K: 925-937.5 MHz
  • Sensitivitet
    <3 μV ved 52 dB (A) rms S/N
  • SPL for peak deviation
    147 dB
  • Støyfilter
    justerbar fra 3 dBμV til 28 dBμV (kombinert med pilottone)
  • Synchronization
    2,4 GHz, laveffekt OQPSK (bare aktiv under synkronisering)
  • Inngangsfølsomhet
    1.5 mV / Pa
  • Audio adjustment range
    45 dB, justerbar i 5 dB trinn
  • Line / Mic level
    20 dB, valgbar
  • Temperaturområde
    bruk: 0 °C til +40 °C, lagring: –20 °C til +70 °C
  • Mottaker prinsipp
    dobbel ”superheterodyne”
  • Diversity-prinsippet
    antennesvitsjing diversity via interne antenner

FAQ

  • How do I find a frequency (ie: perform a frequency scan)?

    To perform a frequency scan on the XS Wireless products follow these steps:

    1) Press the "UP" or "DOWN" button to scroll through the menu options on the receiver.

    2) Press the "SET" button to select the SCAN option. NOTE: The unit automatically selects the next available unused frequency. 

    Once the new frequency is selected on the receiver the transmitter needs to by synced to the receiver. To do this follow these steps:

    1) Press and hold the "SYNC" button on the transmitter until the "SYNC" symbol flashes on the receiver.

    2) Press the "SYNC" button on the receiver.

    NOTE: If a frequency SCAN is performed and no available frequencies are found then the SQUELCH setting will need to be increased. Once the SQUELCH setting has been increased repeat the steps of the frequency scan and then SYNC accordingly.



    XSW 1-908-A ( #507101 )
  • What adjustments can I do to improve sound quality?

    There are two settings that have the greatest effect on sound quality:

    MICROPHONE SENSITIVITY
    This is how sensitivity the microphone pick up is and this is adjusted on the microphone/body pack itself. Typically for general speaking the sensitivity should be set around -15 to -18 dB. You will need to adjust this depending on the exact application. Adjusting closer to 0 dB is will be more sensitive and further away from 0 dB is less sensitive. If the microphone is too sensitive the input will overload the microphone and the AF level will peak and the audio will be clipped.  It is suitable to adjust the level so that the AF peak indicator lights up only briefly during the loudest passages.

    AF OUTPUT
    This is how strong the signal is exiting out of the receiver into the sound board/speakers/etc. Typically this will be set to 0 dB or +6 dB if connected to equipment which is expecting a line level input . If you are connected to equipment expecting a mic level input you will typically need to drop this AF output down to -24 dB or -30 dB.  If your equipment has the option, it is best to try to run the equipment in line level mode.

    NOTE: If the AF Output is too high it may over load the input on any connected equipment (sound board/speakers/etc) and may create noise in the form of distortion/rumbling.



    XSW 1-908-A ( #507101 )
  • Why is there no audio coming from the microphone?

    Not having audio coming from a microphone could be caused by a few different scenarios.
    Firstly check that the transmitter and receiver are both on the same frequency as this is key to the system working.
    Next check to make sure that the "MUTE" switch is not accidentally engaged (either fully or partially). The best way to do this is click the mute switch on and then back off.
    After checking the "MUTE" switch if no audio is present make sure that the microphone element is securely in place. If using a body pack transmitter make sure that the microphone or guitar cable is securely in place by disconnecting it and reconnecting it. NOTE: On the handheld microphone the capsule is locked into place and cannot come loose.
    If you are seeing RF and AF levels on the receiver but do not have any sound through your system it would be recommended to check the cables between the receiver and sound system, check the inputs on the sound system and check the AF out level on the receiver to ensure that it is set to the appropriate level for your sound system.



    XSW 1-908-A ( #507101 )

Nedlastinger

  • Frequency Sheets
    • Frequency Sheet XS Wireless 1&2 K range (925 - 937.5 MHz) (190 KB) Download

    • Frequency Sheet XS Wireless 1&2 B range (614 - 638 MHz) (170 KB) Download

    • Frequency Sheet XS Wireless 1&2 C range (766 - 790 MHz) (160 KB) Download

    • Frequency Sheet XS Wireless 1&2 D range (794 - 806 MHz) (170 KB) Download

    • Frequency Sheet XS Wireless 1&2 E range (821 - 832 / 863 - 865 MHz) (170 KB) Download

    • Frequency Sheet XS Wireless 1&2 GB range (606 - 630 MHz) (210 KB) Download

    • Frequency Sheet XS Wireless 1&2 A range (548 - 572 MHz) (170 KB) Download

    • Frequency Sheet XS Wireless 1&2 JB range (806.125 – 809.750 MHz) (160 KB) Download

  • Technical Data
    • Specifications XS Wireless 1 (2.2 MB) Download

  • Hurtigguider
    • Quick guide XS Wireless 1 (3.5 MB) Download

  • EU samsvarserklæring
    • EU Declaration of Conformity XS Wireless 1 / XS Wireless 2 series (650 KB) Download